It is designed to back-expose and main-finish solvent-washable as well as water-washable, polyester-backed, analogue and digital plates up to a size of 132 x 203 cm (52x80 inch) and thickness up to 7 mm (0.276 inches).
The standard version is equipped with a stress-accumulation early-warning-system and may be equipped with optional tools that enable remote-monitoring and remote-diagnostics.
Exposure 132x203cm (52x80")
The Evo 5 E is an exposure unit in size 132 x 203 cm (52 x 80 inch) with a clam shell system and an automatic pneumatic lid with safety belt for accident prevention. This unit offers a high UV output, constant and uniform also thanks to the light integrator which compensates all the UV output variation. The lamp temperature control is regulated automatically and the machine is equipped with fiber optic for lamps failure detection.
This unit complements the Easy to Plate™ system.
Exposure 120x160 cm (47x63")
This unit is presented with a completely renewed temperature control system. The integrated chiller, along with the new air cooling system for the lamps, as well as the new water cooling system for the exposure table, grant a new level of temperature control precision.
Another convenient solution studied by Vianord is the new control display which can be can be installed either on the left or the right side, according to the customer's preference. The software can memorize up to 24 channels for different plates; which can be stored in the two racks sitated in the machine main body.
The equipment is designed and manufactured according to the EEC safety and health standards, as specified in the Type Examination Certificate No. MA19-0042548-01 (309) issued by IMQ spa – Via Quintiliano 43 – 20138 Milan ITALY, and on the basis of the verifications carried out according to the essential requirements of the Directive 2006/42/EC, the system respects and is in compliance with all the applicable points.
This PLC controlled, stand-alone exposure unit is specifically designed for high quality digital and conventional photopolymer plates for flexible printing applications (e.g. wide web).
One of the most important feature of the Easy to Plate™ is the modularity concept, in other words, each unit is an independent piece of equipment buyable separately with the possibility of being upgraded and attached to one other to compose an all-in-one automatic unit. This gives you two choices: buy the whole automatic line at once, or amortize the investment and buy the different units over a longer time frame.
- High concentration UV-A radiations
- Lamps temperature management
- Controlled airstream for lamps cooling
- Exposure bed temperature management
- Water cooled exposure bed
- Light integrator for compensation of UVA aging lamps
- Vacuum system for analogue plates
Production Data Recording
System Dimensions (net)
320 x 196 x 106 cm w/Lid open 245 cm
126 x 77.1 x 41.7 inch w/Lid open 96.5 inch
System Weight (net)
Industrial Wooden Crates are favoured if the system must withstand multiple transhipments during transport and is mandatory when shipped outside the continent. Dimensions: 348 x 212 x 149 cm (173 x 83.5 x 59.0”)
The dimensions mentioned above are for reference only; packaging dimensions may vary depending on the packing company hired for the job.
The weights mentioned above are for reference only; packaging weight may vary depending on the packing company hired for the job.
Power Supply (field configurable)
360 / 440 Volt – 50 / 60 Hz - 3Ph / N / PE - 207 / 243 Volt – 50 / 60 Hz - 3Ph / PE
Current (nominal load)
11 A (360/440 Volt configuration) - 19 A (207/243 Volt configuration)
Power Rating (nominal)
5 x 4 mm2 (360/440 Volt configuration) - 4 x 6 mm2 (207/243 Volt configuration)
Compressed Air Supply
To perform to the best of its possibilities, the system requires a continuous and stable supply of compressed air at a pressure of at least 7 bar (101.5 psi) and not more than 10 bar (145 psi), with pressure dew point 3°C and max. residual intake oil content of < 0.01 mg/m3. Consider also an average consumption of 70 l/hr. The system installation kit includes a 5-meter - Ø 6mm air connecting pipe for push-in fitting.
The system should be installed in a clean, constant-temperature and constant-humidity pre-printing environment with a temperature between 18 and 26°C (64.4 and 78.8°F) and a non-condensing relative humidity in the range of 40 to 60%.
To maintain such environmental standards an efficient heating/cooling and ventilating system may be required.
Vianord offers all equipment in standard powder coating Vianord Black.
In addition, Vianord offers numerous ways you can personalize your system. In fact, Vianord offers the best customization options in the industry! This allows you to showcase your brand and company’s spirit in ways other companies can’t offer. You can choose your personal colour and have your logo, company name, or slogan pop.